The Enchanted Forest
A lone stag at the focus of a long forest tunnel of wild trees with spiraling branches is my take on a popular origamic architecture/kirigami pop up card theme.
Continue readingSimple Washi Tape Valentine
Quick Celtic key pattern washi tape paper art pop up card for Valentine’s Day.
Continue readingFolding the Dragon
This Lunar New Year marks the start of the Year of the Wood Dragon. I made a video walk-through of making my origamic architecture / kirigami dragon pop up card to celebrate.
Continue readingDragon Pop Up Card
Original origamic architecture / kirigami pop up card of a dragon’s head.
Continue readingMaking of the Garden Lantern Electronic Pop Up Card
The Garden Lantern Electronic Pop Up Card I made in 2017 was one of the first big projects where I shot video documenting the build. There was a lot of footage and, I wasn’t very comfortable with editing videos at that point. The raw video just sat in a folder for a few years. I have done a bunch of build videos since then and, it occurred to me that I could probably manage to pull the old video clips together into a build narrative. I have been slowly putting that together in the last few weeks and, it is finally done!
As I noted in my original post about this project, this was inspired by and based on work done by Jie Qi and Natalie Freed. The Chibitronics Circuit Stickers project made everything a lot easier.
Snow Elf Manor Pop Up Card
A stately origamic architecture / kirigami pop up manor for snow elves, sent for the 2021 winter holidays.
Continue reading180-Degree-Open Pop Up Snowflakes
I played with several variations of this snowflake design back around 2002. There were a couple 180-degree-open card variants that I liked. They were both designed to be cut as four panels that folded together to produce a card with an integrated backing. I had some limited access to a laser cutter for a couple hours to produce the cards. I ended up going with the simpler of the two designs for the production run. That one was less sensitive to smoke deposition and, less fragile.
I always wanted to play with the other design a little more and, in 2020, I finally did a run of those on my own laser.
Smoke deposition was still a challenge, especially on a stock with a pearlescent finish and a little tooth. There is almost always some trade-off with that sort of thing and expedient production. I chose not to apply all of the full repertoire of techniques for these, opting to reduce wear and tear on expensive work-holding mats and, to make production faster.
I made a short production video featuring the jig-in-place technique, dry transfer adhesive and removing stray glue.
Let Glue Dry Pop Up Card
Someone made a paper craft version of the “Let Glue Dry” block Laura Kampf uses in her shop awhile back. I immediately thought of making a pop up card version that could be stored flat. I did one with a simple block font but, later, made another version where I reproduced the hand lettering from a photo of Laura’s block.
I sent one of these to Laura back in March. I am going to assume that it’s okay to share these unless I hear otherwise.
Although I cut my cards on the laser, you could do this entirely by hand with a craft knife. You can even skip the white stickers. The letters could be cut from white paper and glued on. The letters could be colored in with an opaque white marker or paint.
There are two version of each design. The regular one has everything aligned in one image. That is, the score lines for the back show aligned where they should be on the front like a standard OA pattern. The jig-in-place version has the score lines for the reverse flipped for production on a sign or laser cutter.
I made my cards using the jig-in-place technique. In brief, I:
- Stuck the black stock down to an adhesive mat in the Glowforge.
- Disabled all operations except the score lines for the reverse side and the card outline.
- Ran those two operations.
- Flipped the card over in place, aligning it with the hole from which it was cut.
- Placed a strip of white polyester sticker over the face of the card where the white letter would be.
- Disabled the reverse scores and outline cut. Enabled the other operations
- Ran the operations.
- Removed the card and weeded the white polyester stickers.
- Folded the finished card!
I started to make a video of the jig-in-place technique but, it is not super clear on the black stock. I will likely do a video showing how this is done when I have another design on a lighter-colored stock to run.
Files to Make Your Own
These files are for personal, non-commercial use only. Note that, by referencing these, you are agreeing to release any variations you create under identical terms.
LK Let Glue Dry Pop Up Card (Standard version)
LK Let Glue Dry Pop Up Card (Jig-in-Place version)
Echo Coffee OA / Kirigami Pop Up Card
This is a a quick thank you card I made for a local coffee shop I like.
180° Degree Spirals Pop Up Card
In keeping with tradition, I present my 2019 holiday card: a 180° degree opening Celtic spirals abstract origamic architecture / kirigami-style pop up.
